Buy OMRON INDUSTRIAL AUTOMATION E5CK-AA online at Newark element Buy your E5CK-AA from an authorized OMRON INDUSTRIAL. Board in addition to the E5CK-AA Process Controller. For E5AK or E5EK, order an . Connect only an Omron Current Transformer (ECT1 or ECT3). OMRON products are manufactured for use according to proper procedures by a The following tables show the correspondence between the E5CK display.

Author: Malagor Kigaktilar
Country: Monaco
Language: English (Spanish)
Genre: Business
Published (Last): 8 December 2008
Pages: 472
PDF File Size: 4.47 Mb
ePub File Size: 6.42 Mb
ISBN: 608-6-40199-300-9
Downloads: 34472
Price: Free* [*Free Regsitration Required]
Uploader: Voodooramar

Chapters Table Of Contents Got it, continue to print. First-time users should read this chapter without fail. If the communications condition of the host computer and E5CK controller match, then a probable cause is a problem in the communications circuit of one or both of the host com- puter and E5CK controller.

Omron E5CK User Manual

Allen-Bradley L Processor 2. HED Revision code The following table outlines the changes made to the manual during each revision. Page F Action Check the communications condition.

Conventions Used in this Chapter Page 93 These parameters set the communications conditions. Show More Show Less. Show More Show Less. Purchased 2 units, but recieved 2 different versions of the same part. To give priority to stability, increase the set value of this parameter. Read this chapter while referring to the parameter e5ckk in chapter 5. This parameter is automatically set by AT execution.


Checking Indication Accuracy After calibrating input, make sure that you check indication accuracy to make sure that the E5CK controller has been correctly calibrated. If the display remains the same, the E5CK controller must be repaired. Limiter Operation Conditions 4. When changing the manipulated e5k, change it using the keys. Calibrating Current Input 4.


Starting And Stopping Operation 3. Pay Attention to the Following when Installing this Controller F If e5co remove the controller from its case, never touch nor apply shock to the electronic parts inside.

However, note that the power supplies for blocks C exclude relay output and D are shared for the following option unit.

Omron E5CK-AA1-500 Processor/Controller

This mode contains the parameters for setting the basic specifications of the E5CK controller. These parameters are valid when the power is turned ON again or when Function level 0 to 2 modes are switched. Set the control period taking the control characteristics and life expectancy of the controller into consideration. In other words, you cannot switch between the auto and f5ck operations by key operation.

Omrpn the indication accuracy at the upper and lower limits and mid- point.

This item doesn’t belong on this page. How To Use Error Output 7.

The one I could use, great! The LBA is output if the change width of the process value falls below 0. The lowest-priced brand-new, unused, unopened, undamaged item in its original packaging where packaging is applicable. Use this end code to remedy errors that may occur. If the transfer output function is not sup- thermocouple 2 ported, skips steps 7 to The other, well, it’s sitting on my shelf, don’t know what to do with it, it’s an odd duck.


Ensure sufficient space around the controller to allow heat to escape. When adding on the option unit, also see the option unit list on page Checking Operation Restrictions The table below summarizes the main operating restrictions. The dis- play changes to [ ] 20mA calibration display. Calibrating Thermocouple When the process value display is flashing, the process value is not saved as data even if the key is pressed. F Action Check the communications condition.

So, control outputs and auxiliary output are turned OFF. Auxiliary Output 1 Assignment Setup Mode Auxiliary output 1 assignment Assigns output functions to auxiliary output 1.

Purchased 2 units, but recieved 2 different versions of the same part. The total resis- tance of both ends should be at least If the transfer output function is not supported, skip to step Transfer output upper limit Transfer output lower omrob These parameters set the transfer output conditions.

Command Configuration The start character.