Before you start to use SSL, please read these instructions carefully to enjoy RX/RX/RXT receiver and the SANWA SUPER VORTEX STOCK ESC . In case of using M11X with RXR, the typical servos (like analog servos) and the For additional information, please read official manual for each product. Page 1 of GHz Radio Control System User Manual Sanwa Electronic . If using an M11X, MX-3X, Gemini X or other FH3 transmitter, choose FH3.
|Published (Last):||4 May 2017|
|PDF File Size:||20.65 Mb|
|ePub File Size:||18.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sanwa M11X Manuals
Any modifications or abuse of the product will void the warranty. Page 19 end point adjustment 3 Test-run your model to set the brake adjustment using the Trm 5 switch. Also, conduct checks with sanwa m11x manual transmitter as distant as possible from your model to ensure adequate reception distance.
Transmitter and receiver Binding is also accomplished sanwa m11x manual the Set-Up menu. Once the binding procedure is complete, the bind code is remembered manuzl when the transmitter and receiver are turned OFF. Comments to this Manuals Sanwa m11x manual Name. This allows you to use the transmitter with different models and quickly and easily select the programming for each of them.
However, there is no guarantee that interference will not occur in a particular installation. Each Push-Button Switch is programmable and will perform a different function depending on what function is assigned to it. The default setting is 0.
For example, when set to a negative value, you can stop the engine with only the press of a button. Compensation Mixing compensation mixing Function Page 2 C-MIX The Compensation Sanwa m11x manual function allows you to mix two channels together, then apply that mixing to the channels themselves. Trm sanwa m11x manual is factory set at the top center position.
It sanwaa you to perform several different functions depending on how the Throttle Hold function is set up. The battery is charged directly through the transmitter, using the charging jack located at the base of the grip.
The Fail Safe function can be programmed independently on all four channels and three options are available: A Receiver Battery Voltage Fail Sanwa m11x manual function is also featured, however, it is used with glow- or gas-powered models.
To get the most out of your experience, we recommend the sanwa m11x manual of digital servos.
92082 2.4GHz Radio Control System User Manual Sanwa Electronic Instrument Co Ltd
Servo Monitor servo monitor Function Page 2 SERVO The Servo Monitor function displays the output levels of the four different channels in bar graph sanwz, allowing you to monitor sanwa m11x manual operation sanwaa a virtual sanwa m11x manual. This makes it easier to start the engine.
For information about programming the Fail Safe function, refer to your transmitter User’s Guide. This allows you to take advantage of the higher torque and higher speed provided by using high-voltage 7.
Page of 67 Go. For more information about the Channel Response Mode function and how to program it, refer to your transmitter User’s Guide. Table of Contents Add sanwa m11x manual my manuals Add. With the transmitter set to 4CH Mode, a desired amount of braking can be applied independently sanwa sanwa m11x manual manual it possible to obtain safer engine starts by applying the brakes while still keeping throttle open a desired amount.
SANWA M11X MANUAL PDF
When the transmitter is subsequently turned ON, sanwa m11x manual last menu and function page that was displayed when the transmitter was sanwa m11x manual OFF is displayed. The bind code is unique to each transmitter and receiver pair, so you cannot bind more than one transmitter to the receiver at the same time and you don’t need to worry about other users’ transmitters interfering with your receiver.
Refers to the throttle trigger stroke that engages the brakes on sanwa m11x manual model pushing the throttle trigger. Use of any other charger can damage the transmitter. This allows you to see servo movement and make setting changes without having the sanwa m11x manual turned on. Page 62 FH2 Modulation: Trm 1 is factory set at the top center position.
The Fail Safe function can be set to Hold the servos in the last position they were in when the signal was lost, or manuak of the servos can be manuall to move to a sanwa m11x manual position when the signal is lost. In this case, turn both the transmitter and receiver OFF, then repeat the binding procedure again. Binary data sanwa m11x manual, use -b option to extract Instance ID: It’s not necessary to program this feature when used with an ESC.